Hasselblad Flextight 848 Manual de usuario

User's GuideFlextight 848English

Back Panel & ConnectorsA Power Cable Socket: plug the power cable into this socket.B FireWire Interface Sockets: plug a FireWire cable (max. 6 m)

Cut-Away ViewA CCD Housing: this movable platform contains the light sensor andholds the optics.B Positioning Lead Screws: for positioning of the CCD

Setting up the ScannerEnvironmental RequirementsSet up the scanner in a location that fulfils the following requirements:•Keep the scanner away from s

Installation Procedure, FireWire Interface1. Place the scanner on a table near your computer with the frontfacing away from you. Make sure that the lo

User's Guide - Flextight 848Hardware Reference - Flextight 84814Operating InstructionsEnglishABKLCFLEXTIGHT ORIGINAL HOLDERPATENTPENDINGààààDEGHJ

Operating Instructions(See Figure 4 opposite).1. It is assumed that the scanner and FlexColor software have beenproperly installed.2. If not already d

User's Guide - Flextight 848Hardware Reference - Flextight 84816Operating InstructionsEnglishABKLCFLEXTIGHT ORIGINAL HOLDERPATENTPENDINGààààDEGHJ

...continuedNOTE! Each original holder has it's own unique identification code(a combination of small rectangular holes at the holder's lead

...continued9. Lay the top layer of the holder down flat over the original.•For transparency holders, the top layer is magnetic, which willhold the or

ResolutionsTrue ResolutionsThe table below shows the max. resolutions (in ppi) available with eachof the original holders when scanning in True Resolu

© 2004 Hasselblad A/S. All rights reserved.Flextight 848 User's Guide, Part No 70030049, revision A.The information in this manual is furnished f

Calibrating the ScannerThe scanner requires two types of calibration:•Focus calibration adjusts the positioning of the scanners optics foreach zoom le

Focus CalibrationThe Flextight 848 scanner uses an adjustable zoom and focus mechanismto optimize its scanning resolution for each of the original for

White Calibration for ReflectivesThe Flextight scanner uses a white reference to make sure that allelements in the scanner's CCD react consistent

5. Click on Calibrate. The scanner will take several scans of the whitetarget. The process will take about eight minutes.User's Guide - Flextight

User's Guide - Flextight 848EnglishHardware Reference - Flextight 84824The Light TubesPRESSPULL OUTPULL OUTPRESSàAEBCGDF12Figure 7: Replacing the

The Light TubesGeneralThe Flextight 848 contains two light tubes: one for illuminating reflectiveoriginals from above, the other for shining light thr

User's Guide - Flextight 848EnglishHardware Reference - Flextight 84826The Light TubesPRESSPULL OUTPULL OUTPRESSàAEBCGDF12Figure 7: Replacing the

...continued8. Remove the defective tube:•Press the flaps backwards to release the tube.•Pull the tube gently out of the holders and then sideways out

Technical SpecificationsPower Connector:Power ConsumptionMax. 60 W during operationPower Requirements100-240V AC, 1.3A, 50-60HzInterface to ComputerFi

FCC NoticeThis equipment has been tested and found to comply with the limits fora Class A digital device, pursuant to Part 15 of the FCC Rules. Thesel

Table of ContentsUser's Guide - Flextight 848Table of Contents3EnglishHardware Reference - Flextight 848 5Warnings and Restrictions 6System Requi

CE - Declaration of conformityUser's Guide - Flextight 848Hardware Reference - Flextight 84830CE - Declaration of conformityEnglishHASSELBLAD A/S

User's Guide - Flextight 8484English

Hardware Reference - Flextight848This manual provides important information about using your Flextight848 scanner.Topics include:•Important warnings a

Warnings and Restrictions•Read all of the included documentation before attempting to installand use the scanner.•Do not touch the originals and/or th

System RequirementsBelow are the basic hardware requirements for the PC or Macintoshsystem to which the scanner is to be connected.For information abo

User's Guide - Flextight 848Hardware Reference - Flextight 8488English

Front PanelA Feed Table: must be in lower position for normal scanning. Whenscanner is not in use you can turn it to upright position flushing withthe